UTS
英
美
abbr. 抗张强度极限；拉力强度（极限）(Ultimate Tensile Strength); 水下电话系统(Underwater Telephone System); 统一传输系统(Unified Transfer System)
双语例句
- The improvement of YTS is attributed to the grain refinement strengthening of Y and Zn, and to the solid solution strengthening of Zn. The reduction of UTS and elongation are caused by the precipitation of a compound phase along the grain boundary.
Y、Zn元素的细晶强化及Zn元素的固溶强化是屈服强度提高的主要原因；抗拉强度和延伸率的降低是由于化合物相沿晶界析出。 - It is shown that the ultimate tensile strength ( UTS) torsion failure life ( TEL) and reverse bending failure life ( RBFL) are decreased obviously as the consequences of the zincing.
研究结果表明，热镀锌使双相钢冷拔钢丝的抗拉强度、扭转寿命和弯曲寿命降低。 - CW_PA, ceramometal alloy, joined by laser welding machine, was tested by the UTS, SEM and metallographic_examination. The good results show that it can be applied to the clinic.
激光焊接CWPA烤瓷合金，测试其力学性能，作金相，SEM分析，结果表明完全达到临床要求。 - Influence of fibre length on UTS and reliability of mullite/ zl109 Composites
纤维长度对M/ZL109复合材料强度及可靠性的影响 - The Unmanned Turret System ( UTS) is the developing direction for future fire system. The UTS is relatively secure to the crew members when the tank and armored vehicle turret is hit with a high probability.
无人炮塔系统是未来火力系统发展的方向，在坦克和装甲车辆炮塔部分被命中概率高的现实情况下，无人炮塔对乘员来说相对安全。 - It is suggested that the pressure for solidification mostly affected the early and last dimension of the air holes, and the last dimension of the air hole played an important role for the UTS of the mullite short fibre reinforced Al matrix composites.
结果表明，气孔类残余孔洞初始尺寸和最终尺寸与保压压强有关，并显著影响莫来石短纤维增强铝基复合材料的拉伸强度。 - It is feasible to forecast the casting UTS by measuring DAS, but the effect of hole ratio on UTS should not be neglected.
通过测定二次枝晶间距来预测铸件的抗拉性能是可行的，但是孔洞率对抗拉强度的影响不可忽视。 - Compared with peak aging alloys, the ultimate tensile strength ( UTS) of two-step aging alloys reduced by about 13%, but UTS of regression-reaging treated alloys excelled that of peak aging alloys.
同时发现，双级时效合金的抗拉强度比峰时效合金的强度下降了13%左右，而回归再时效合金的强度优于峰时效合金的强度。 - The results show that the addition of Y and Zn improves YTS values but decreases the UTS and elongation values of as-cast alloys.
结果表明：Y、Zn元素提高了合金的屈服强度但降低了抗拉强度和延伸率。 - The output parameters of the model are three mechanical properties namely ultimate tensile strength ( UTS), yield strength ( YS) and elongation ( ELO).
模型的输出为三个力学性能指标，即抗拉强度、屈服强度和延伸率。